Are you planning on building a rabbit house for your pet rabbit or for a bunch of rabbits? Just follow these simple steps and you'll have that rabbit housing ready for your little friend at the end of the day. You don't need to sweat on it too much if you are just starting out on keeping rabbits. The project itself takes about 2-4 hours to finish unless you are to make a bigger hutch. Here are the things you need to have for your project:
- 2x2 lumber wood
- Plywood
- Mesh wire
- Hardware cloth
- Saw, hammer, -1 inch nails, deck screws
- Fencing staples
- Wood glue
- Hinges
- Paint (optional)
Before you start hammering away, take a look at the few steps you need to consider in making a rabbit housing. It's important that you follow these chronologically without hesitations.
Step 1: Illustrate or draw out a plan that you can follow. A plan is very helpful in minimizing work time and keeps you going. Write down the measurements of each side and corner. This plan will be your guide as to how and what the rabbit housing will look like. This will only take you a few minutes so pour out your idea on that piece of paper!
Step 2: Prepare your work space. It would be better if your work space is outside your home. All the materials must be nearby you so you can reach for them without any problem if you are working alone.
Step 3: Lay down the 2x2 lumber on the floor or the ground and mark it according to the measurement you prefer. Cut the 2x2 lumber for the rabbit housing frame. You can make a frame that's up to 8 feet if you have more than 2 rabbits. Lay the lumber down on the ground of your work area. You can use deck screws or nails and reinforce it with wood glue if you so wishes. Fasten the corners of the frame.
Step 4: If the base frame is already done, put hinges on the top frame. Be sure that the measurement of the frame is deep enough and wide enough for the rabbit to run in. This will be the door for the rabbit or rabbits.
Step 5: Enclose the frame. Be sure that you have enough to cover all area. Cut the plywood according to the desired measurement you have.
Step 6: Spread the mesh wire and hardware cloth and nail them together to the frame. Use fencing staples to keep them in their right positions.
Step 7: Once the hutch is finished you can paint it with any color you like. Let the rabbit housing dry with its door opened.
Finally, a wide hutch for your pet rabbit. No need to worry about your little furry friend when it runs around the house. It can already enjoy and hop around its new rabbit housing safe from harm.
- 2x2 lumber wood
- Plywood
- Mesh wire
- Hardware cloth
- Saw, hammer, -1 inch nails, deck screws
- Fencing staples
- Wood glue
- Hinges
- Paint (optional)
Before you start hammering away, take a look at the few steps you need to consider in making a rabbit housing. It's important that you follow these chronologically without hesitations.
Step 1: Illustrate or draw out a plan that you can follow. A plan is very helpful in minimizing work time and keeps you going. Write down the measurements of each side and corner. This plan will be your guide as to how and what the rabbit housing will look like. This will only take you a few minutes so pour out your idea on that piece of paper!
Step 2: Prepare your work space. It would be better if your work space is outside your home. All the materials must be nearby you so you can reach for them without any problem if you are working alone.
Step 3: Lay down the 2x2 lumber on the floor or the ground and mark it according to the measurement you prefer. Cut the 2x2 lumber for the rabbit housing frame. You can make a frame that's up to 8 feet if you have more than 2 rabbits. Lay the lumber down on the ground of your work area. You can use deck screws or nails and reinforce it with wood glue if you so wishes. Fasten the corners of the frame.
Step 4: If the base frame is already done, put hinges on the top frame. Be sure that the measurement of the frame is deep enough and wide enough for the rabbit to run in. This will be the door for the rabbit or rabbits.
Step 5: Enclose the frame. Be sure that you have enough to cover all area. Cut the plywood according to the desired measurement you have.
Step 6: Spread the mesh wire and hardware cloth and nail them together to the frame. Use fencing staples to keep them in their right positions.
Step 7: Once the hutch is finished you can paint it with any color you like. Let the rabbit housing dry with its door opened.
Finally, a wide hutch for your pet rabbit. No need to worry about your little furry friend when it runs around the house. It can already enjoy and hop around its new rabbit housing safe from harm.
About the Author:
Learn the right way and guide about rabbit farming business the first time and avoid having to make painful errors that beginner rabbit owner's are prone too. Acquire more help on how to build an easy rabbit hutch at: www.howtoraiserabbits.com
No comments:
Post a Comment